Deploying NSX-T v2.4 for Enterprise PKS
Page last updated:
Warning: Pivotal Container Service (PKS)
v1.3 is no longer supported because it has reached the End
of General Support (EOGS) phase as defined by the
Support Lifecycle Policy.
To stay up to date with the latest software and security updates, upgrade to a supported version.
To deploy NSX-T for Pivotal Container Service (PKS), complete the following set of procedures, in the order presented.
Note: The instructions provided in this topic are for NSX-T v2.4. If you are using NSX-T v2.3.1, see Deploying NSX-T v2.3.1 for Enterprise PKS.
Before you begin this procedure, ensure that you have successfully completed all preceding steps for installing PKS on vSphere with NSX-T, including:
- vSphere with NSX-T Version Requirements
- Hardware Requirements for PKS on vSphere with NSX-T
- NSX-T Deployment Topologies for PKS
- Preparing to Deploy PKS with NSX-T on vSphere
This section describes the NSX-T v2.4 management interface options, differences, use cases, and recommendations.
Note: NSX-T v2.4 implements a new Policy API and a new NSX Manager user interface (UI) based on the Policy API. Enterprise PKS does not support the Policy API or Policy-based UI. Enterprise PKS supports the NSX Management API, which is exposed via the “Advanced Networking” tab of the of the NSX Manager UI. When installing and configuring NSX-T v2.4 for use with Enterprise PKS, use the “Advanced Networking” tab to create any required networking objects.
With NSX-T 2.4 you have two options to interact with NSX Manager:
- New declarative interface introduced in NSX-T 2.4 that uses the new Declarative API/Data Model (Policy API).
- The NSX-T Container Plugin (NCP) that is embedded in the Enterprise PKS tile does not support the Policy API at this time.
- You cannot use the Simplified UI/API to manage NSX-T for use with Enterprise PKS upgrades and new installations.
- Legacy imperative interface based on the NSX Management API.
- Provides the NSX-T v2.3 user interface to address Enterprise PKS installation and upgrade use cases. Currently NCP only supports the Management API.
- The Advanced UI/API will be deprecated over time; all features and use cases will eventually be transfered to the Simplified UI/API.
As shown in the picture below, for all Enterprise PKS workloads, use the Advanced Networking and Security tab to create, read, update, and delete required network objects. For NSX-T host perparation and configuration, such as deploying NSX Managers and Edge Nodes, use the System tab. Do not use the “Simplified UI” for Enterprise PKS objects.
Note: The NSX-T Container Plugin (NCP) that is embedded in the Enterprise PKS tile does not currently support the Policy API. Make sure you use the **Advanced Networking and Security** tab of the of the NSX Manager UI when configuring NSX-T for use with Enterprise PKS.
In the case of upgrade from NSX-T v2.3 to v2.4, the existing NSX-T v2.3 configuration is copied to NSX-T v2.4 under the Advanced Networking and Security tab. The network objects required by PKS can only be managed from this user interface. In other words, this configuration will not be shown in the Simplified UI. When you upgrade to NSX-T v2.4, the Simplified UI will show a information banner that indicates the objects are available in the “Advanced Networking” tab.
For instructions on upgrading NSX-T from v2.3 to v2.4 for Enterprise PKS, see Upgrading Enterprise PKS with NSX-T.
To perform a new installation of NSX-T v2.4 with Enterprise PKS v1.4, complete the steps.
- Prepare for Installing NSX-T 2.4.
- Install NSX Manager using the System tab.
- Deploy Additional NSX Manager Nodes to Form a Management Cluster using the System tab.
- Assign a Virtual IP Address and Certificate to the NSX-T Manager Cluster using the System tab.
- Install One or More Pairs of NSX Edge Nodes using the System tab.
Warning: For Enterprise PKS you must install a large size VM form factor or the bare metal Edge Node. See Deploy NSX Edge Nodes for more information.
- Create an NSX Edge Cluster using the System tab.
- Join NSX Edge Nodes with the Management Plane using the System tab.
- Enable Repository Service on NSX Manager. Repeat this step for each NSX Manager.
- Create an IP Pool for Tunnel Endpoint IP Addresses using the System tab.
- Create Overlay and VLAN Transport Zones using the System tab.
- Create an Uplink Profile using the System tab.
- Create Edge Transport Nodes using the System tab.
- Configure Edge Nodes for HA using the System tab.
- Prepare ESXi Hosts as Transport Nodes for NSX-T using the System tab.
- Create a Tier-0 Logical Router using the Advanced Networking and Security tab in NSX Manager.
- Create the Enterprise PKS Management Plane using the Advanced Networking and Security tab in NSX Manager.
- Create the PKS Compute Plane using the Advanced Networking and Security tab in NSX Manager.
- Deploy Ops Manager 2.4.3+.
- Generate and Register the NSX Manager Cluster Certificate (if you have not already done so).
- Configure BOSH Director with NSX-T for Enterprise PKS.
- Generate and Register the NSX Manager Superuser Principal Identity Certificate and Key.
- Create NSX-T Objects for Enterprise PKS using the System tab in NSX Manager.
- Install Enterprise PKS on vSphere with NSX-T v2.4.
Please send any feedback you have to firstname.lastname@example.org.